Drolet CS1200 Dokumentacja Strona 1

READ AND KEEP THIS MANUAL FOR REFERENCE 45109A.doc INSTRUCTIONS & OPERATIONS MANUAL DROLET EE1200 WOODSTOVES: ML, RC, LITTLE SAWMAN AND COM

9TYPICAL INSTALLATIONS FACTORY BUILT CHIMNEY: ROOF FLASHING18" CLEARANCEWALL SUPPORTWALL RADIATION SHIELDRAIN CAP Wall installation CEILIN

10MASONRY CHIMNEY: Clay liner Thimble Clean out door

11FACTORY BUILT THIMBLE:

12BRICK THIMBLE:

13WOODSTOVE UTILISATION Your heating unit was designed to burn wood only; no other materials should be burnt. Wastes and other flammable materials s

14Smaller pieces of wood will dry faster. All logs exceeding 6" in diameter should be split. The wood should not be stored directly on the gro

15ASH DISPOSAL Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always empty the stove when it is cold

16AIR CIRCULATION SYSTEM In order to improve air circulation in the room where the wood stove is installed, certain options are available for specifi

17• NEVERS OPERATE THE STOVE WITHOUT A GASKET OR WITH A BROKEN ONE. DAMAGE TO THE STOVE OR EVEN HOUSE FIRE MAY RESULT PAINT Only clean your stove w

18FREQUENTLY ASKED QUESTIONS WHAT DO THE WORDS “DRAFT” AND “NEGATIVE PRESSURE” MEAN? The word “draft” refers to the hot air movement that circulates

1 TABLE OF CONTENTS INTRODUCTION... 2 A

193- Wind can also be a third cause of negative pressure. When your house is located near a structure which height is superior to your roof’s, win

20DRAWING #1 DRAWING #1 shows a stove functioning under normal and adequate conditions. Heat rises to the upper floors and the room where the stove

21 DRAWING #2 DRAWING #2 shows the effect of a cold chimney. Cold air creates a reverse draft (negative pressure), which causes smoking problems.

22 DRAWING #3 DRAWING #3 shows the effect of negative pressure caused by an air-moving device inside the house. In the example above, the range

23 DRAWING #4 DRAWING #4 shows the negative pressure effect caused by wind, influenced by nearby structures such as a building.

24 DRAWING #5 DRAWING #5 shows the negative pressure effect that can be caused by wind, influenced by nearby structures such as a tree.

25CAN I MODIFY MY STOVE TO INSTALL A GLASS DOOR? It is forbidden to modify a stove. Stoves are safety tested with a specific configuration, drawing

26 1700, rue Léon-Harmel, Québec (Québec) G1N 4R9 tel. : (418) 527-3060 fax : (418) 527-4311 e-mail : [email protected] web site : www.drolet.ca

2INTRODUCTION STOVE BUILDER INTERNATIONAL INC., one of the most important wood stove and fireplace manufacturers in Canada, congratulates you on you

3 ASSEMBLY Legs installation: Position the stove on its back and screw the legs in place with 8 screws, 8 bolts, and 8 washers; Ash lip Installa

4 Cast iron flue collar installation:1. Peel off the tape from the back of the gasket and attach the gasket to the rope groove at the back of the

5INSTALLATION SAFETY NOTICE • IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY RESULT. TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATIO

6 CLEARANCES FROM COMBUSTIBLES It is of outmost importance that the clearances to combustible materials be scrupulously respected upon installation o

7 CHIMNEY Your wood stove may be hooked up with a factory built or masonry chimney. If you are using a factory built chimney, it must comply with UL

8CHIMNEY CONNECTOR (STOVE PIPE) The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021" or 0.53 mm. It